DIY Name Sign & High Chair Banner
I think I've fallen in love with making these banners & name signs! The perfect addition to personalize birthdays and special occasions. I made a name sign for my friends baby shower and a high chair banner for my sons birthday. I hope that she can use this banner in her daughters nursery or to help celebrate any other special occasion for her baby girl!
I love how you there customizable, reusable, and make such a great keepsake!
What you'll need:
(contains paid links)
Embroidery machine. I use the Brother SE 700 machine, and LOVE it.
Fabric + Ribbon. ( I found my fabric and ribbon at Hobby Lobby! )
Iron
How To:
I've seen so many talented people make these name signs and banners and theres so many different methods, tips, and tricks for making them! This is simply what has worked best for me after some trial and error. So feel free to take what works for you and make it your own!
Step 1: Prep your materials
First I like to prep all my materials. Cut out squares of fabric for each letter, you will need one piece for the front and one piece for the back of each letter. You will also need to cut a piece of embroidery foam for each letter.
Then apply HeatnBond Lite to the back of each piece of fabric, this will help with frayed edges.
Step 2: Prep your embroidery hoop
Place your stabilizer in your embroidery hoop, making sure its pulled nice and tight.
Next, spray some temporary adhesive onto the stabilizer and place down your foam. I like to then add some more adhesive and then lay my fabric on top.
When it comes to sizing and placement I tend to eyeball everything because I've made these before! If you want to be more precise and know exactly how much you need, and where you need to place your materials, you can run a tack down stitch on your stabilizer before placing down your materials to see exactly where you need to place everything.
Step 3: Load your design and begin
Load your hoop into your machine, and make sure your bobbin thread is wound with the same color as your top thread.
I purchased both the design and font from Etsy and downloaded them into the Artspira app. With my machine I can transfer them straight over to my machine.
You can find the exact design + font I used here:
(contains paid links)
For the font I used the 2.5 inch !!
Step 4: Run a tack down stitch
Once your design is transferred over to your machine your going to run your first tack down stitch. I only run this stitch once in the beginning, but you can run another tack down stitch before placing your materials if you want to check the placement before hand.
Step 5: Embroider your letter
Next, skip ahead to the step where you'll embroider your letter. On my machine I pay attention to the numbers in the right corner which show me which step I'm on, It also gives me a preview of what that step is. You'll want to pay attention to these steps because you wont be stitching in order for this design.
Step 6: Add the back fabric
Remove your hoop for the machine, flip your design over, and add on your back piece of fabric with adhesive spray.
Step 7: Run a tack down stitch
Place your hoop back into your machine and go back to the step where you'll run a tack down stitch, and run that again.
Step 8: Trim around your design
Remove your hoop, and carefully trim as close to the tack down sticth as you can, removing the excess fabric. Trimming carefully will help create those clean scolloped edges!
Trim the front and the back.
Step 9: Run your satin stitch
Once everything is trimmed, place your hoop back into your machine and run your satin stitch.
Take your hoop out and carefully remove the foam around your deisgn.
Run your satin stitch again! I just recently tried this, running my satin stitch twice. Once before and after I remove the foam, and I love how clean the edges look when doing this!!
Your design should now pop out of the stabilizer nicely. I then go ahead and clean everything up. You can use heat, I like to use my iron, to clean up any extra foam pieces on the edges and smooth everything out.
Step 10: Add your Ribbon
Using a leather hole punch, cut out the designated holes at the top for the design.
Thread your ribbon through the holes, and your finished!!
Your name sign is complete!!
I hope these directions help in your name banner process. Again, this is what has worked for me personally after some trial and error. So of course you can take what works for you and make it your own!
If you like more of a visual when it comes to tutorials you can watch the tutorial I made by clicking here!

If your interested in how I made this Baby shower gift you can find the details by clicking here!

Thank you so much for stopping by and reading this post! I hope you found a little inspo for your next project!
Happy Crafting!
Sam


Comments